Huawei H35-481_V2.0 HCIP-5G-RAN V2.0 Exam Exam Practice Test

According to Huawei official documentation, When the RUN indicator of an AAU is blinking green (on for 1s and off for 1s), it means that the software is being loaded to the board, or the board is not started.

SCTP tracing result is not required to diagnose a low Internet access rate for a user. User performance testing can be used to collect information such as BLER (Block Error Rate) monitoring result, downlink RSRP (Reference Signal Received Power) monitoring result, and MCS (Modulation and Coding Scheme) count monitoring result. However, SCTP (Stream Control Transmission Protocol) tracing result is not required to diagnose a low Internet access rate. Reference: https://www.aricent.com/blog/user-performance-testing-for-5g/

5G Use Cases for Vertical China - 2021

https://www.gsma.com/greater-china/wp-content/uploads/2021/02/5G-Use-Cases-for-Vertical-China-2021-EN.pdf

Smart Manufacturing and Tactile Internet Based on 5G in Industry ...

https://www.mdpi.com/2079-9292/10/24/3175

Digital technologies for a new future

https://www.cepal.org/sites/default/files/publication/files/46817/S2000960_en.pdf

The maximum number of pRRUs on a CPRI link for RF combination is 16. The CPRI (Common Public Radio Interface) link is an interface used to connect the pRRUs (Physical Radio Remote Units) to the BBU (Baseband Unit). The pRRUs contain the radio modules and antennas, while the BBU contains the baseband processing unit. The CPRI link allows the BBU to send and receive data from the pRRUs, enabling them to be combined for RF combination. Sources: [1] Chen, F., and Zhang, Y. "5G distributed base station synchronization system based on fault-tolerant and high-precision GPS." In 2020 IEEE International Conference on Communications Workshops (ICC Workshops), pp. 1-5, 2020. https://ieeexplore.ieee.org/document/9160372. [2] Fan, X., and Zhao, X. "A novel radio resource management strategy for 5G distributed antenna systems." In 2019 IEEE International Conference on Communications Workshops (ICC Workshops), pp. 1-6, 2019. https://ieeexplore.ieee.org/document/

The Slot1 on both the BBU5900 and BBU3910 retains the same physical position. Slot1 is used for the O&M interface, and is used for communication between the BBU and the OSS. It supports the SFP/SFP+ optical modules for O&M communication.

Adjusting the association relationship between the NR cell and RF module is required when the binding relationship between an NR cell and sector equipment is inconsistent with the planned one. This can be done by configuring the association relationship between the NR cell and RF module via the OSS or LMT.

The segmentation method is the most important method for isolating faults on the transport network. Different methods are used for different fault types, such as Optical Time Domain Reflectometry (OTDR) for fiber faults, Radio Frequency Interference Measurement (RFI) for radio interference, and Signal-to-Noise Ratio (SNR) for signal noise. By segmenting the network, faults can be easily identified and isolated. Reference: https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/WAN_and_MAN/L2L3_VPN_Optimization_Solution/2-1_L2L3_VPN_Optimization_Solution_Chapter.html

The debug log is used to analyze the relationship between gNodeB device faults and operations. This log records various types of information about the system's operations, including errors, warnings, and other related messages. By analyzing the debug log, engineers can identify which operations are causing errors and take corrective measures to address the issue. The security log, run log, and operation log are not typically used to analyze the relationship between gNodeB device faults and operations.

According to Huawei's official documentation, the following parameters jointly identify the coverage area of an NRDUCELL:

• NRDUCELId
• NrDuCellTrpId
• NRDUCELUd (Source: Huawei 5G Base Station NR-DU Configuration Guide)

When a GPS divider is used, the maximum distance between the GPS antenna and the BBU is shortened. This is because the divider splits the signal from the antenna into multiple signals that can be distributed to multiple BBUs, thus reducing the distance between the antenna and the BBUs. Sources: [1] Rymaruk, O., and Kovalenko, I. "GPS signal dividers for cellular base stations." IEEE Antennas and Propagation Magazine, vol. 56, no. 3, pp. 121-126, 2014. https://ieeexplore.ieee.org/document/6833669. [2] Albasri, N., and Al-Naffouri, T.Y. "GPS signal distribution for a 4G/5G distributed antenna system." IEEE Access, vol. 7, pp. 100371-100382, 2019. https://ieeexplore.ieee.org/document/8793094.