Activedumpsnet Logo
What components are required to create a storage view?
Refer to the exhibit.
A customer is requesting a performance analysis for their distributed volumes in a Metro configuration to ensure there are no issues with a recent implementation.
What additional files should be collected?
Which command allows you to navigate vplexcli history by string?
What can you use to generate a list of VPLEX fabric initiator and target identifiers?
You are preparing a site for a large Metro VPLEX cluster. The storage administrator wants to prepare the storage network configuration and needs to ensure easy troubleshooting of storage path faults.
How many WAN-COM zones per fabric will need to be created?
What are the recommended protection and disk type when selecting a VPLEX Logging Volume?
What is the total number of available engines in the smallest VPLEX Metro configuration?
You are zoning a dual-engine Local VPLEX cluster to a Symmetrix array to see LUNs 0010 and 0020 for metadata backups.
How many directors in the cluster must be zoned and masked to these LUNs?
A customer has a quad-engine VPLEX Metro configuration and has stated they want to review their performance metrics from the past 4 hrs on the entire cluster. How many performing log files will they need to pull from the management server in order to analyze all of their components?
Refer to the exhibit.
Which two metavolume candidates should be used to complete the displayed command?
During the installation of a VPLEX Local, the command ‘configuration system-setup’ is issued. What is accomplished by this command?
You created a synchronous consistency group, which contains two distributed volumes configured with the rule "set cluster-1-detaches".
What is the expected behavior of the virtual volumes in the event of a WAN-COM failure?
A VPLEX administrator claims a 100GB Storage Volume that is thin provisioned on the storage array and has 25GB physically allocated and creates a 1:1 encapsulated virtual volume. After a local data mobility job for that Virtual Volume, the storage array administrator notices that the allocated capacity has increased to 100GB. Why did this happen?
What is the recommended protection to be used when creating a VPLEX Logging Volume?
A customer wants to refresh the underlying array that comprises one-half of their local RAID-1 mirrors. Their intent is to remove the discarded mirror from VPLEX control, but as a rollback procedure, they want to ensure the detached device is a consistent copy of the original data. What is the proper way to perform this operation, meeting the customer's requirements?
Where is the wwn-seed physically located on VS2 engines?
Do virtual volumes need to be taken off-line prior to upgrading VPLEX software, and why or whynot?
Which type of volume has complete synchronized copies of data (mirrors) in more than one cluster?
When should front-end ports be enabled during a VPLEX installation?
What is the EMC best practice for the optimum number of back-end storage paths per director presented to a LUN?
In which asynchronous Consistency Group Operation stage are the delta sets written to the storage arrays?
Refer to the exhibit.
You have created a Distributed Device in a VPLEX Metro. You want to confirm you have chosen the correct volumes before performing a device mobility job within cluster-2. Which object will be the source for this operation?
Which command would you execute to perform basic system checks to ensure that the VPLEX cluster is working properly?
A customer has asked you to inspect their SAN connectivity before upgrading their Local configuration to a Metro. What will the output of the connectivity validate-be command provide for an analysis of this environment?
Refer to the exhibit.
During a short power disruption to cluster 2, director-2-1-A failed. Power was restored after 5 minutes. In examining the output of the vault status command, you note that cluster-2's status reads "Cluster is not vaulting/unvaulting".
Why did this message appear?
What function does the SNMP agent on the Management Server provide?
Click on the calculator icon in the upper left corner of the screen. A customer has ordered a new VPLEX, and you are on site doing the initial installation. When creating metadata volumes for the VPLEX Local configuration, the customer asks you how much total storage is needed for the VPLEX metadata.
According to EMC best practices, what is the total minimum storage needed for this configuration?
A VPlex administrator claims a 100GB Storage Volume that is thin provisioned on the storage array and has 25GB physically allocated and creates a 1:1 encapsulated virtual volume. After a local data mobility job for that Virtual Volume, the storage array administrator notices that the allocated capacity has increased to 100GB.
Why did this happen?
Refer to the exhibit.
What does this 4-step VPLEX cache operation represent?
What is a key advantage of integrating VPLEX into a VMware environment?
What device types can be created in a VPLEX environment?