Brocade 170-010 Brocade Certified vRouter Engineer Exam Practice Test

vyatta@Vyatta1:~$ show firewall name PublicServers statistics

IPv4 Firewall "PublicServers":

Active on (eth0,IN)

rule packets bytes action source destination

---- ------- ----- ------ ------ -----------

10 210 15960 ACCEPT 10.2.3.0/24 10.6.7.0/24

20 40827 2731049 ACCEPT 10.4.5.0/24 10.6.7.0/24

30 69381 4192375 REJECT 10.4.5.0/24 10.6.7.0/24

40 89538 5366257 ACCEPT 0.0.0.0/0 10.6.7.0/24

10000 82866 5289591 DROP 0.0.0.0/0 0.0.0.0/0

Based on the output shown, which statement is true about this firewall configuration?

What is the maximum number of domain names a vRouter can advertise using Dynamic DNS?

You are using the ? key for more information regarding this command:

vyatta@vyatta:~$ show ip ospf?

What will be the result?

Which command disables hello packets on an OSPF interface?

VLAN 10 is configured on ethernet 0.

Which command line will display operational statistics for the VLAN?

Which two show commands will confirm that a device is receiving OSPF external routes? (Choose two.)

A user has read-write access to a Brocade Vyatta vRouter.

Which two commands will display the current device configuration? (Choose two.)

Data is being transmitted from host A to host B.

If you were to capture a frame at the point indicated in the exhibit, what would the source MAC address be?

Which term describes a single port on an Ethernet switch?

Which three commands display whether a firewall rule has been matched by traffic? (Choose three.)

What information does a router need to add an entry to its routing table? (Choose two.)

vyatta@VYA1:~$ show ip route ospf

O 192.168.12.0/24 [110/1] is directly connected, eth2, 00:07:36

O 192.168.13.0/24 [110/1] is directly connected, eth3, 00:07:36

O *> 192.168.23.0/24 [110/2] via 192.168.12.2, eth2, 00:05:05

*> [110/2] via 192.168.13.3, eth3, 00:05:05

O 192.168.101.0/24 [110/1] is directly connected, eth1, 00:07:36

O *> 192.168.128.0/24 [110/2] via 192.168.12.2, eth2, 00:05:53

O *> 192.168.129.2/32 [110/11] via 192.168.12.2, eth2, 00:05:53

O *> 192.168.130.2/32 [110/11] via 192.168.12.2, eth2, 00:05:53

O *> 192.168.131.2/32 [110/11] via 192.168.12.2, eth2, 00:05:53

O *> 192.168.160.0/24 [110/2] via 192.168.13.3, eth3, 00:05:05

O *> 192.168.161.3/32 [110/11] via 192.168.13.3, eth3, 00:05:05

O *> 192.168.162.3/32 [110/11] via 192.168.13.3, eth3, 00:05:05

O *> 192.168.163.3/32 [110/11] via 192.168.13.3, eth3, 00:05:05

vyatta@VYA1:~$ show ip route summary

IP routing table name is Default-IP-Routing-Table(0)

IP routing table maximum-paths is 8

Route Source Networks

connected 7

static 1

ospf 9

Total 17

FIB 9

vyatta@VYA1:~$

With all routing settings at system defaults, which statement is true about the interface VYA1 will use to transmit traffic destined for 192.168.23.15?